LOCTITEABP8068TH/5C0ABLESTIK ABP 8068TH – 2.5cc in 5cc syringe - 2989860
Chương trình đóng rắn khuyến nghị: Với kích thước chip ≤3 x 3 mm: tăng nhiệt 5°C/phút từ 25°C lên 150°C, giữ 30–60 phút; tăng 5°C/phút lên 200°C, giữ 90–120 phút, trong lò N2. Với kích thước chip >3 x 3 mm: tăng nhiệt 5°C/phút từ 25°C lên 150°C, giữ 30–90 phút; tăng 5°C/phút lên 200°C, giữ 90–120 phút, trong lò N2. Rã đông: Để hộp đạt nhiệt độ phòng trước khi sử dụng. Sau khi lấy ra khỏi tủ đông, đặt ống tiêm thẳng đứng trong lúc rã đông. Thời gian rã đông phụ thuộc vào kích cỡ ống tiêm. Tham khảo hướng dẫn xử lý để biết thêm thông tin. KHÔNG mở hộp khi nội dung chưa đạt 25°C. Mọi hơi ẩm đọng trên hộp sau khi rã đông cần được lau khô trước khi mở. KHÔNG đông lạnh lại. Khi đã rã đông về 25°C, keo không được đông lạnh lại. Hướng dẫn sử dụng: Keo đã rã đông cần được đưa vào thiết bị châm keo ngay để sử dụng. Nếu chuyển keo sang bình chứa châm keo cuối cùng, cần cẩn thận tránh để tạp chất và/hoặc không khí lọt vào keo. Keo phải được sử dụng hết trong thời gian sử dụng khuyến nghị của sản phẩm. Có thể dùng lượng châm keo khác tùy theo yêu cầu ứng dụng. Mẫu châm hình sao hoặc hình chữ thập sẽ tạo ít bọt khí trong lớp keo hơn so với mẫu châm dạng lưới.
Recommended cure schedule For the die size <= 3 x 3 mm 5°C/mins ramp from 25°C to 150°C, hold for 30-60 minutes 5°C/mins ramp to 200°C, hold for 90-120 minutes, N2 oven For the die size > 3 x 3 mm 5°C/mins ramp from 25°C to 150°C, hold for 30-90 minutes 5°C/mins ramp to 200°C, hold for 90-120 minutes, N2 oven Thawing Allow container to reach room temperature before use. After removing from the freezer, set the syringes to stand vertically while thawing. Thaw times depend on the syringe size. Consult handling guide for more information. DO NOT open the container before contents reach 25°C temperature. Any moisture that collects on the thawed container should be removed prior to opening the container. DO NOT re-freeze. Once thawed to 25°C, the adhesive should not be re-frozen. Direction for use Thawed material should immediately be placed on dispense equipment for use. If the adhesive is transferred to a final dispensing reservoir, care must be exercised to avoid entrapment of contaminants and/or air into the adhesive. Adhesive must be completely used within the product's recommended work life. Alternate dispense amounts may be used depending on the application requirements. Star or crossed shaped dispense patterns will yield fewer bondline voids than the matrix style of dispense pattern.

















![LOCTITE ABLESTIK ABP 8068TH – 2.5cc in 5cc syringe - 2989860 [ABP8068TH/5C0]](https://image.chanhvinh.com/anh/loctite/m/loctite-abp8068th-5c0-1.webp)